Bracket, New Style

Front lifting handle for the Hummel

$68.66

Item # HS030NS

Control Rod, Upper, New Style

Upper control rod for the Hummel With locking collar

$54.32

Item # HS081NS

Conversion Feather Paddle Kit

Conversion Kit to upgrade your Hummel to the new style feather handle. Paddle design to use the palm of your hand. Works very smoothly with a ball bearing pivot. Kit includes everything you need to convert machines made after 1990. If your upper control rod is bent, worn, or is older and not fitting correctly you will also need to replace part number HS081.

$335.13

Item # HS079NS

Hummel Fuse, new style

Replacement fuses for the Hummel belt sander. These fuses are a hard to find size. 6 1/4 amps. Fuse measures 1 1/4 x 1/4 (6.3mm x 32mm) For larger old style fuses, order HSFUSE

$14.00

Item # HSFUSEN

Hummel Run Capacitor Aftermarket

Replacement 40mfd Run Capicator for Lagler Hummel Floor Sander A lower cost alternative to the HS205 original, this uses an off the shelf capacitor with a custom housing to mount like the original. Direct replacement.

$80.00

Item # HS205A

Hummel Start Cap, Aftermarket

A lower cost alternative to the HS153, this uses an off the shelf/ US style capacitor with a custom housing to mount like the original. For use on Hummel sanders only, do not use on edgers!

$80.00

Item # HS153A

Lower Rod Assembly, New Style

Lower Control rod for the Hummel Includes wing nut

$102.71

Item # HS138NS

Metric screw, hex, 8 x 16

$1.00

Item # XBAIJ

Power Wires for HSSW

Replacement switch wires for HSSW box. This includes: Black wire from inlet to switch White wire from inlet to switch Black wire from switch to terminal block White wire from switch to terminal block Wires from switch to power meter All wires come with the required terminals installed.

$15.00

Item # HSSWP

Resistor, Start Capacitor

This is the discharge resistor on the Hummel start capacitor. This is not required to function, but it prolongs capacitor life. It also discharges any stored power in the capacitor.

$10.00

Item # HS829

Start Switch, Aftermarket

Electronic start switch similar to the CL38 Sinpac switch. Can be used to replace the CL38. The case size is smaller (1-3/8 inch diameter x 2-3/4 inch long), and the terminals are in a different order (3 2 4 1). When installing, be sure to connect the wires to the correct terminal number. See install video: https://youtu.be/Ul21bGRjl_I

$165.00

Item # CL38B

Start Switch, Square

Electronic start switch similar to the CL38 Sinpac switch. This functions differently than the CL38, so it is not a direct fit replacement. (There is a change to the wiring.) Rated for .6 to 6 horsepower 220 volt motors. Not rated for use on Galaxy motors (they are 7.5 horsepower). Used on all HSSW boxes sold after 3/24/2021

$50.00

Item # CL38A

Wheel Truck New Style

$277.44

Item # HS1565

Wing Nut, Dust Pipe

$20.34

Item # HS028NS

Wire Brush 8 hummel size

8 Wide wire brush drum. Fits the Hummel as well as some Lagler drum sanders. May have to remove upper roller assembly to fit older machines with steel frame upper roller. Machines from 2002 on have aluminum upper roller arms.

$1,200.00

Item # SA8H

Washer, fender, 5/16

$1.00

Item # XOCG

80g Belt Blue Zir 77/8x29.5

7-7/8 x 29-1/2 blue zirconium sanding belts. These are our economy sanding belts. They are zirconium for durability, yet priced very affordable. Zirconia grain X weight backing S seam 10 per box Known as our blue belts

$4.60

Item # USBB80

Voltage Meter, 20 Amp Plugs~

Low voltage is the main cause of burned up motors. This inline voltage meter allows you to watch the voltage while sanding. Since the voltage loss of a power cord depends on the load, this is the only way of knowing your operating voltage. Comes with male & female 20 amp twist lock plugs (Nema L620) Note: This is a voltage meter, not a power booster.

$150.00

Item # KM02

30 Amp Circuit Breaker Switch*

These 2-pole circuit breaker switches are used on most Clarke/Alto sanders. This is 30 amp with push connect terminals, standard for most machines.

$98.00

Item # K840

Plug, M, 250v 20amp* 620P

NEMA L6-20 20 amp 250 volt grounding twist-lock male plug. This is the standard size used on the Hummel & Clarke/Alto machines. Eaton Cooper Arrow Hart Brand

$12.12

Item # 6212

Inlet 250v 20amp* 620FI

NEMA L6-20 20 amp 250 volt grounding twist-lock male flanged inlet. This is the standard size used on the Hummel & Clarke/Alto machines. Eaton Cooper Arrow Hart Brand

$24.54

Item # 6215

Bearing, Ball, 6005-2RS

Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.

$10.00

Item # 6005

Bearing, Ball, 6201-2RS

Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.

$7.00

Item # 6201

Bearing, Ball, 6202-2RSH C3

Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.

$7.00

Item # 6202

Bearing, Ball, 6205-2RS

Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.

$12.00

Item # 6205

Bearing, Ball, 6206-2RS

Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.

$14.00

Item # 6206

Sander Cord 75 20Amp^

Sander power cord made with 10/3 non marking gray or yellow cord. 75 Foot long, with 20 amp twist lock plugs (Nema L620). Do not run more than 100 ft. without a power booster.

$322.88

Item # SC7520

Axle

Axle for the rear caster on the old style dual yoke caster for the Hummel. This consists of the following items: XBAKY Metric screw, hex head, 12 x 80 XFAK Metric Nut, hex, 12mm

$2.57

Item # HS100

Bag, Sander Generic Hummel

Replacement dust bag for the Hummel sander. This generic bag is the same size as the OEM, but is made from a red cloth.

$19.98

Item # HS225H

Base, Tension Roller Lower

$396.38

Item # HS927

Bearing Ball 5202-2RS (3202-2RS)

This is a double row bearing, which means it has 2 rows of balls instead of the usual 1, which gives it a higher load rating. Normally used where a shaft is supported by a single bearing. Same size as 3202 bearing Same as 3202 bearing except for radius on edge of bearing.

$18.00

Item # 5202

Bearing Bush~

Bushing for the upper roller lever eccentric on the Hummel Sander

$32.16

Item # HS117

Belt Guard, Complete~

$365.50

Item # HS055

Belt Tension Arm US Made

Heavy duty steel replacement fan belt tensioner arm for the Hummel Works with the HS066 pulley

$90.48

Item # HS065

Belt Tensioner, Complete OEM

Fan belt tension pulley with bracket for Hummel

$367.44

Item # HS064

Belt, Drum Hummel 17x875

Drum Belt for Lagler Hummel Floor Sander Original Gates power metric belt

$44.23

Item # HS186

Belt, Fan Hummel Gates10x670

Fan Belt for Lagler Hummel Floor Sander Original Gates power metric belt

$26.00

Item # HS187

Bracket

Front lifting handle for the Hummel

$60.34

Item # HS030

Cable Support, Complete

Cord holder for Hummel. Includes O-ring. Note - replacement O-ring is part # UE31

$62.14

Item # HS082

Cap Kit, Control Rod

Cap kit with snap on cap to hold control rod to feather handle on Hummel

$6.00

Item # HS087C

Capacitor, Run 40mfd*

$32.01

Item # HSSWR

Capacitor, Run, 40mfd

OEM Running Capacitor for the Lagler Hummel and Elf sanders. For a lower cost alternative, consider HS205A instead.

$258.96

Item # HS205

Capacitor, Start, 108-130mfd*

$25.00

Item # HSSWS

Capacitor, Start, 130mfd

OEM 130mfd Starting Capacitor for the Lagler Hummel and Elf sanders. Some very old machines may have a 60mfd capacitor instead; see HS153-60. For a lower cost alternative on Hummel sanders, consider HS153A instead (HS153A cannot be used on edgers).

$339.54

Item # HS153

Carry Handle Hummel

For carrying sanders up and down stairs. Fits Hummel, Appolo, Classic and Floorcrafter.

$147.90

Item # HS835

Circlip, 18mm

$2.08

Item # HS130

clip ring, 1

$1.00

Item # XMBO

clip ring, 9/16

$1.00

Item # XMBK

Clip, Top Roller

$31.65

Item # HS912

Collar Nut

Assembly that holds the bottom of side drum door on the Hummel

$22.62

Item # HS051

Collar Rubber NS Boot

$113.75

Item # HS815

Compression Spring

Spring for the upper roller assembly on the Hummel Sander This is the spring that pushes the roller up. If this spring is weak it can give you tracking problems

$31.46

Item # HS121

Compression Spring

Spring for the tracking adjuster on the Hummel sander upper roller

$22.73

Item # HS123

Cone Roller/CL31^*

Edge guide/cone roller for the Hummel Sander. Assembled with bearings, threaded stud, and nut. Replacement bearings for this roller is # 626 OEM roller available under part # HS108

$65.00

Item # HS21

Connector, Female (motor box)

$62.42

Item # HS827

Control Rod, Upper

Upper control rod for the Hummel With locking collar

$75.51

Item # HS081

Cover Fastener

Latch to hold top of the drum side door on the Hummel

$39.74

Item # HS049

Cover, Side Door

Side drum door for Hummel

$83.44

Item # HS048

Dolly, Hummel^

These travel dollys have 5 inch diameter x 2 inch wide grey non marking rubber wheels to roll smoothly even on rough terrain. They have a spring pin to attach them firmly yet allow quick removal. No machine modifications. Slides on and of in seconds, so it is not in the way while sanding. Fits 8 Hummel belt sanders. ***Green Powder Coated Frame last longs and scratches less*** Now updated to fit newer machines! Also available for the Galaxy, KT, and Bona HD

$250.00

Item # HSDOLLY

Double Arm Complete ActuatorNS

$87.42

Item # HS914

Drum, Hummel 8

Original factory new drum from Lagler. Fits the Hummel 8 This drum is football shaped from the factory for improved tracking. See #RHS8 to get your drum recovered, or HS161R to purchase a remanufactured drum We will buy your new style Hummel drum cores for $40 each* * Must be tin end, not the older solid core. Aluminum core must be in good condition with both end caps attached and no cracks or damage.

$809.69

Item # HS161

E-stop Mount Plate

$30.80

Item # HS249

Edge Roller Assy

Wall guide / edger roller for Hummel Sander The wheel only is available to replace. See part number HS042.

$153.01

Item # HS102

Emg Conn. Shell Motor

$62.08

Item # HS826

Exchange Hummel 8 Drum Recovery

Price reflects a $300.00 core fee that will be refunded when we receive an acceptable core (see terms & conditions for acceptable cores).Recovered Hummel 8 black rubber drum. This drum is tapered (football shaped) similar to OEM. Recovered to factory size with serrations. It is balanced to same specs as OEM. Same durometer rubber as OEM. This item is an exchange drum. If we do not have your drum first for exchange we will charge you a refundable core fee (reflected in price) and ship out our drum to you before we receive your core. You must return your old core within ten days with a copy of the invoice to receive you core refund. Your old core must be in good condition without any defects or wear to receive a full core refund. The customer pays the return shipping. Always ship insured and keep a copy of the tracking information. Call for availability. Availability is not shown online.

$730.00

Item # RXHS8

Eye Bolt

$26.74

Item # HS197

Eye Bolt

Eye bolt for attaching an operator belt to the Hummel machine. The threads are 8mm.

$25.26

Item # HS256

Fan Cover

$103.61

Item # HS217

Fan Housing

$403.21

Item # HS170

Fan Insert, Complete

Fan assembly for Hummel floor sander. Fan assembly is pressed together. With correct care the bearings can be changed, however if not done properly the unit will fail. Video on how to remove the fan assembly on a Hummel.

$596.65

Item # HS169

Fan Motor Cooling

$57.47

Item # HS216

Floor Sander Drum Puller 8 10 12

For removing drums from Floor Sander belt sanders. This large puller fits 8, 10 or 12 inch drums up to 7.5 inch diameter. Has a hardened 5/8-18 screw that can be turned with a 15/16 wrench or socket. We also have a smaller puller for removing drums on EZ8 sanders (EZPUL).

$102.74

Item # SW09

Fuse Holder, New Style

This is a newer, low profile fuse holder. Includes everything you need to retrofit from the old style. Takes new style fuses (HSFUSEN). Note the old style fuse holders are no longer available.

$48.93

Item # HS813

Grip

Plastic grip for the front handle on the Hummel

$57.55

Item # HS031

Guide Roller Lower Chasis

$154.03

Item # HS280

Guide Tube~

Guide tube or dust pipe for Hummel

$465.05

Item # HS076

Handle Replacement, Phenolic

Replacement Handle for left or right on newest style Hummel bullet style handles Does not fit the old style handles from the 90s

$41.18

Item # HS078

housing ring, 1.75

$2.00

Item # XMCT

housing ring, 2

$2.00

Item # XMCU

housing ring, 32mm

$1.00

Item # XNCT

Housing~

$3,109.93

Item # HS021

Hummel Fuse, old style

Replacement fuses for the Hummel belt sander. These fuses are a hard to find metric size. 6 1/4 amps. Fuse measures 1 1/2 x 13/32 (10mm x 38mm) For smaller new style fuses, order HSFUSEN

$20.52

Item # HSFUSE

Hummel Switch Box Modification^*

Using off the shelf components, you can retrofit your Hummel motor control box for a little more than the price of a single OEM component. This box uses a circuit breaker switch and an electronic start module in place of the original rotary switch. Now has a volt meter built into the box. For instructions on hooking this up, see the wiring diagram https://store.ussander.com/download_files/hssw.pdf Also check out our YouTube installation videos: https://www.youtube.com/playlist?list=PL3_0KULLIuJp7Ac8SSWhQzMz3U9H6sTya All boxes built after 3/24/2021 use a square start switch instead of the round Sinpac switch. We have videos detailing how to change from the Sinpac to the square switch https://youtu.be/coK0Hg7JE-0 and how to change the new square switch back to a Sinpac https://youtu.be/mfXS-owVgmI.

$350.00

Item # HSSW

Hummel Wheel New Style Flat

Made out of plastic Teflon type material. New style wheel for machines made after the 2000s Replaceable bearing These wheels have a flat bottom and do not mark soft floors as easily. This is our customer requested design. for original pointed type wheel use part # HS149

$60.00

Item # HS149W

Idler Pulley, steel^

Replacement Idler pulley for Hummel fan belt tensioner. Steel pulley with bearing and stud. Includes washers to space pulley. Depending on the year of the sander more or less washers will be needed. Punch out and remove your old pulley stud and install this long lasting steel pulley with replaceable #6000 bearing.

$80.00

Item # HS066

Intake Duct~

$528.38

Item # HS168

Key (Long)

$5.57

Item # HS163

Key for Motor Pulley Hummel

Metric Key for Hummel 8 Floor Sander Motor Pulley.

$6.64

Item # HS220

Key, Drum Shaft Pulley, NS(10m

$4.89

Item # HS975

Kill Switch w/ Red Button

$105.72

Item # HS836

Knob, Ball

Ball knob push on style for Hummel feather handle

$22.02

Item # HS083

Lever, Drum control

Drum lever or feather handle for Hummel If there is play in your handle you should replace this item or install a new bushing from US Sander # HS080A This does not include the ball knob

$105.89

Item # HS080

Lifting Fixture wheel truck

$287.82

Item # HS133

Long Handle Assy

New style handle kit. This is the kit you need if you have the old style handles to upgrade with this complete kit. All of the old style parts are not available and this kit must be used.

$95.91

Item # HS079

Lower Rod

Lower Control rod for the Hummel Includes wing nut

$84.67

Item # HS138

Met. Key, oval, 6 x 25

$3.00

Item # XLBHN

Met. Key, oval, 6 x 40

$2.00

Item # XLBHQ

Met. Nut, hex, 8

$1.00

Item # XFAI

Met. Nut, jam, 10

$1.00

Item # XFDJ

Met. Nut, lock, 8

$1.00

Item # XFCI

Met. Washer, fender, 8

$4.00

Item # XPCI

Met. Washer, sae, 6

$1.00

Item # XPAH

Met. Washer, sae, 8

$1.00

Item # XPAI

Met. Washer, Shim, 16 x .5

$1.00

Item # XPGM

Met. Washer, tooth lock, 6

$1.00

Item # XPEH

Met. Washer, tooth lock, 8

$1.00

Item # XPEI

Metric screw, cone point, 8 x 12

$1.00

Item # XBIIG

Metric screw, flat, 5 x 30

$1.00

Item # XBCGO

Metric screw, hex, 6 x 16

$1.00

Item # XBAHJ

Metric screw, hex, 8 x 20

$1.00

Item # XBAIL

Metric screw, hex, 8 x 50

$1.00

Item # XBAIS

Metric screw, hex, 8 x 60

$1.00

Item # XBAIU

Metric screw, low socket, 8 x 12

$2.00

Item # XBYIG

Metric screw, low socket, 8 x 16

$1.00

Item # XBYIJ

Metric screw, pan, 5 x 12

$1.00

Item # XBBGG

Metric screw, pan, 5 x 6

$1.00

Item # XBBGD

Metric screw, socket, 6 x 16

$1.00

Item # XBEHJ

Metric screw, socket, 6 x 50

$1.00

Item # XBEHS

Metric screw, socket, 8 x 20

$1.00

Item # XBEIL

Metric screw, socket, 8 x 25

$1.00

Item # XBEIN

Metric screw, socket, 8 x 35

$1.00

Item # XBEIP

Motor Bearing Bracket

$153.29

Item # HS193

Motor Mounting

$108.78

Item # HS192

Motor Nut

$43.82

Item # HS194

Motor Pulley

$274.48

Item # HS214

Motor Tensioner

$66.65

Item # HS195

Motor, Complete

$5,285.49

Item # HS185

Notch Plate

Tension selector notch plate for Hummel

$51.04

Item # HS137

Nozzle Box, Shell Cord End

Will not fit old strain relief! Need to replace strain relief with HS1415

$41.98

Item # HS825

Nut, Hex LH Drum

$42.98

Item # HS159

Nut, Hex RH

$42.98

Item # HS158

Nut, Replacement, Control Rod

$18.89

Item # HS283

O Ring

$2.81

Item # HS260

Oil Seal, Shaft

$53.40

Item # HS166

Operating Lever

Lever to raise and lower the upper roller on the Hummel Sander

$29.32

Item # HS115

Pan Head Screw

$2.18

Item # HS261

Pin Insert, Cable End Kill Swi

$53.42

Item # HS824

Pivot Pin

Pin for the lower control rod and wheel truck on the Hummel

$13.85

Item # HS134

Plastic Bushing

Plastic chassis bushing for the wheel axle on the Hummel Sander. If your Hummel is creating waves this is one of the items you should replace to make sure your machine is moving freely. You also need to make sure the wheel axle/arm is not worn, dirty, or galled and moves freely with the wheel truck removed. Replace the axle/arm if there are any of the mentioned problems with a new axle/arm # HS151.

$21.80

Item # HS1110

Pulley Drum, V belt

$265.52

Item # HS160

push cap, 5/16

$1.00

Item # XMDG

PVC Tube

PVC cover for the rear safety guard/carry handle on the Hummel

$15.97

Item # HS038

Rear Wheel Complete w/Yoke

Rear wheel with yoke for Hummel This is the new style wheel with the new style single yoke caster.

$352.89

Item # HS091

Rear Wheel, New Style OEM

Rear Caster wheel with bearing for Hummel Fit the caster yoke that only has one yoke OEM This is the tapered plastic wheel. If you want a flat wheel for soft floors see item # HS02N

$139.20

Item # HS099NS

Rebuilt Hum Mtr w/ Ctrl Box^

Hummel motors will burn up with low voltage. This is why we recommend running no longer than a 75 foot cord without a power booster. However, if your motor does burn up, we have these rewound motors. These are available by exchange only - we must get a rewindable motor in exchange.

$2,115.94

Item # HSMRTB

Roller Top w/Axle Assy OEM

8 upper roller for the Hummel Sander Includes the center shaft and the bearings installed OEM tapered rubber coated If your roller is not slightly higher in the center, does not have even rubber on both sides, and/or undersized it is time to change your upper roller to improve your tracking.

$337.37

Item # HS110

Round Head Screw

Always use blue thread locker (Loctite 242 or similar) when installing.

$1.00

Item # HS915

Safety Belt

Operator belt made by Lagler for the Hummel

$195.35

Item # HS254

Safety Guard, Complete

Also called the rear carry handle for the Hummel

$71.09

Item # HS037

Sander Bag, OEM Hummel

OEM Replacement dust bag for the Hummel sander.

$101.78

Item # HS225

Sanding Shaft

$350.89

Item # HS154

Screw Stud

Stud for the drive belt guard to hold guard closed on Hummel

$39.25

Item # HS059

Screw, Fan, New Style

$2.00

Item # HS180N

Screw, Fan, Old Style

$1.50

Item # HS180

Screw, Wing

Control rod wing bolt to attach the upper lower rods on the Hummel Steel wide flat knob welded to bolt.

$12.56

Item # HS145

Seal, Drum Shaft, NS

$51.03

Item # HS1141

Sealing Plate

$27.19

Item # HS272

Sealing Ring

$30.89

Item # HS171

Sealing, Felt

Sealing felt for the front edge of the Hummel Helps improve dust collection

$42.83

Item # HS023

Shaft, Drum 2000+ NS

$321.21

Item # HS154NS

Side Wheel w/Bearing NS OEM

Original plastic Hummel side wheel New style wheel for machines made 2002 or newer These wheels have a V bottom For flat wheels that do not mark soft floors as easily use part # HS149W

$120.65

Item # HS149

Slide Ring

$45.99

Item # HS156

Spacer Ring, Old

$44.68

Item # HS157

Spacer Ring, Shaft NS

$35.03

Item # HS1140

Spacer, Castor Pivot

Shim washer for above the rear wheel yoke. 4 shims standard. Adding more shims will make the machine cut more aggressively.

$5.40

Item # HS386

Spring Tensioner

Tension lever selector for Hummel

$74.89

Item # HS135

Stop Collar Rod

$4.00

Item # HS081C

Strain Relief Union

Nut not included - order HS495

$49.24

Item # HS208

Strain Relief, Old Style

This is the old style strain relief - will not fit the new HS825 (Use HS1415 instead)

$29.32

Item # HS654

Support, Tension Roller Upper

$392.56

Item # HS918

Switch Box 220-230v

$232.65

Item # HS279

Switch Emergency Kill Assy

$569.83

Item # HS808

Switch Knob

$38.41

Item # HS203

Switch, Rotary Original

Switch for Hummel Floor Sander by Lagler.

$458.24

Item # HS202

Tension Spring w/HS136 Screw

Drum pressure tension spring for the Hummel Includes the tension adjuster bolt and nuts When you change this you will have to set the machine back up the factory drum pressure. Setting bolt back to the same height will get it close but it may still be off. Too much pressure could overheat the motor. If you are getting reduced drum pressure or are getting waves you may want to change this. If you are getting waves also purchase the HS1110 bushings.

$30.46

Item # HS140

Tire Side Wheel Old Style Hummel

This is the old style Hummel side wheel for machines 2001 and older that have not been upgraded to new style wheels. Fits older style Hummel with the screw on cover over the wheel. Plastic Teflon Type Material OEM sizes Flat bottom wheel so it does not dent softer floors

$47.70

Item # HS01

Tire, Rear Old Style Hummel

This is the old style Hummel rear wheel. Fits older style Hummel with the double yoke rear caster 2001 and older Plastic Teflon Type Material OEM size Flat bottom wheel so it does not dent softer floors

$54.94

Item # HS02

Top Roller Cam

$173.15

Item # HS913

Top Roller Unit Complete

Upper roller assembly for the Hummel Sander This includes handle to lower the roller. This is the easiest way to fix tracking problems created from bad upper roller parts or loose linkages and bushings.

$1,421.70

Item # HS107

Universal Contactor

Contactor / relay for the Hummel.

$380.00

Item # HS278

Voltage Meter

$11.00

Item # HSSWM

Washer, fender, 1/4

$1.00

Item # XOCF

Washer, thick fender, 1/4

$1.00

Item # XOHF

Wheel Arm Assy

$124.22

Item # HS151

Wheel, Lateral Complete

$204.38

Item # HS147

Wheel, Rear, New Style

This is the new style Hummel rear wheel. Fits newer style Hummel with the single yoke rear caster 2002 and newer Plastic Teflon Type Material, OEM size and diameter, Flat bottom wheel for softer floors

$49.50

Item # HS02N

Wing Nut, Dust Pipe

$20.34

Item # HS028

Yoke Housing

$220.46

Item # HS271

Setting Fixture (level tool)

Level tool for the Hummel. Use this tool to level the wheel to the frame of the machine. If you are installing a new drum this will level the drum to the floor or make a good starting point to have the machine level. If your drum is old the drum could be worn and may not be square to the machine and will need leveled by eye. Hummel Leveling Tool

$66.55

Item # HS233