Hummel Accessories Upgrades

Conversion Feather Paddle Kit

Conversion Kit to upgrade your Hummel to the new style feather handle. Paddle design to use the palm of your hand. Works very smoothly with a ball bearing pivot. Kit includes everything you need to convert machines made after 1990. If your upper control rod is bent, worn, or is older and not fitting correctly you will also need to replace part number HS081...

$184.32

Item # HS079NS

Bag Clamp

This quick release bag clamp makes removing & reattaching dust bags easier on sanders. The clamp when fully expanded has a diameter of 4 inches. Colors may vary...

$21.00

Item # SN001

Carry Handle Hummel

For carrying sanders up and down stairs. Fits Hummel, Appolo, Classic and Floorcrafter...

$107.04

Item # HS835

Dolly, Hummel^

Note: These do not fit the redesigned Hummel machines release late 2022 These machines can be identified by the serial number tag on the lower right side of the machine. These travel dollys have 5 inch diameter x 2 inch wide grey non marking rubber wheels to roll smoothly even on rough terrain. They have a spring pin to attach them firmly yet allow quick removal. No machine modifications. Slides on and of in seconds, so it is not in the way while sanding. Fits 8 Hummel belt sanders. ***Green Powder Coated Frame last longs and scratches harder*** Also available for the Galaxy, KT, and Bona HD..

$250.00

Item # HSDOLLY

Drum, Hummel 8 New

Original factory new drum from Lagler. Fits the Hummel 8 This drum is football shaped from the factory for improved tracking. See #RHS8 for our recovered drums...

$588.64

Item # HS161

Hum Switch Box Modification^*

Using off the shelf components, you can retrofit your Hummel motor control box for a little more than the price of a single OEM component. This box uses a circuit breaker switch and an electronic start module in place of the original rotary switch. Now has a volt meter built into the box. For instructions on hooking this up, see the wiring diagram https://store.ussander.com/download_files/hssw.pdf Also check out our YouTube installation videos: https://www.youtube.com/playlist?list=PL3_0KULLIuJp7Ac8SSWhQzMz3U9H6sTya All boxes built after 3/24/2021 use a square start switch instead of the round Sinpac switch. We have videos detailing how to change from the Sinpac to the square switch https://youtu.be/coK0Hg7JE-0 and how to change the new square switch back to a Sinpac https://youtu.be/mfXS-owVgmI...

$350.00

Item # HSSW

Hummel Fuse, old style

Replacement fuses for the Hummel belt sander. These fuses are a hard to find metric size. 6 1/4 amps. Fuse measures 1 1/2 x 13/32 (10mm x 38mm) For smaller new style fuses, order HSFUSEN..

$18.00

Item # HSFUSE

Hummel LED Light Kit

New Hummel 8 LED Light Kit by Lagler Ultra-bright LED light (3480 lumens) 30w Includes new electric box cover with mount for light. Light conversion kits will be available to purchase for machines that were built in 1988 and later. There is some wiring involved...

$496.41

Item # HS770

Multi-Clip, bag clamp

Bag clamp OEM Hummel style..

$14.50

Item # HS018

Puller Drum 8 10 12

For removing drums from belt sanders. This large puller fits 8, 10 or 12 drums up to 7.5 diameter. Has a hardened 5/8-18 screw that can be turned with a 15/16 wrench or socket...

$90.00

Item # SW09

Rebuilt Hum Mtr w/ Ctrl Box^

Hummel motors will burn up with low voltage. This is why we recommend running no longer than a 75 foot cord without a power booster. However, if your motor does burn up, we have these rewound motors. These are available by exchange only - we must get a rewindable motor in exchange...

$1,812.23

Item # HSMRTB

Rewound Field Exchange 8*

Hummel motors will burn up with low voltage. This is why we recommend running no longer than a 75 foot cord without a power booster. However, if your motor does burn up, we have these rewound motors. These are available by exchange only - we must get a rewindable motor in exchange...

$1,632.15

Item # HSMFIELD

Safety Belt

Operator belt made by Lagler for the Hummel..

$146.19

Item # HS254

Setting Fixture (level tool)

Level tool for the Hummel. Use this tool to level the wheel to the frame of the machine. If you are installing a new drum this will level the drum to the floor or make a good starting point to have the machine level. If your drum is old the drum could be worn and may not be square to the machine and will need leveled by eye. Hummel Leveling Tool..

$57.53

Item # HS233

Voltage Meter Kit

This kit is to install a voltage meter on a machine. Kit includes panel mount meter and a hole saw...

$27.00

Item # KM05