Super 7R Accessories Upgrades

Edger Chair, Folding

The Edger Chair is a backsaver for floor sanding professionals. The Edger Chair can be used to sit and lean forward on or rotate the seat post to sit on it as a rolling stool. You can use the Edger Chair in almost any size area including halls and closets. Folds flat for easy storage 4 wheels for stability Use an edger with a bag or a dustless system hose Powder-coated steel construction Adjustable height Chest pad easily adjustable forward or backward Clip for cord management Built in sandpaper tray..

$725.00

Item # EDOLLY

Latch, Edger Case, Metal

Replacement latch for new style Super 7 & B-2 edger cases. This is a single latch, cases have 2. For old style cases with plastic latches, order E05...

$13.42

Item # E06

Pigtail w/Plug, Edger

16 Long pigtail with male twist lock plug. Fits Super 7, B-2 & Silverline edgers. May also fit some others...

$36.92

Item # EC03

Edger Bulb LED

LED bulb with ceramic base will fit in existing light sockets for a much longer service life than standard bulbs. 5 watt LED with 37 watt output 400+ lumen Very bright slightly blue colored bulb to help show scratches better. Made of ceramic and metal base with a clear plastic cover. Fits the Super 7, B-2, and Silver Line Edgers. This is much brighter than the new Clarke LED that is a 2.6w bulb. Note - For use on 120 volt edgers only. This will not work on 240 volt power. For 240V use part # E10LE..

$10.99

Item # E13LE

Edger Cord Assy 1 Super 7^

..

$67.03

Item # EC02

Super Edger Pad S7 B2

Edger Pad for Floor Sanding Edgers. Fits Clarke Super 7 & B-2, Galaxy Elite and SilverLine edgers. This super pad is made from billet aluminum with an OEM style rubber face. We designed these pads because we were tired of hearing complaints about bent edger pads. We have been making them since 2006, and have only seen 1 that got bent. Billet Aluminum More rubber to dress than original pads. Precision ground and balanced. Made in USA...

$92.58

Item # USE01

Edger Pad Adjust Removal Tool

For removing and installing edger pads. This adjustable wrench can be adjusted to fit all edger pads...

$46.70

Item # E20A

Switch, LD Edger

On-Off toggle switches for Floor Sanding edgers. These are a 2-pole switch. Light Duty. Regular (Light) duty 15 amp @110v Edger switch for most Clarke Edgers S7 (Super 7R) & B2 If you would like a more heavy duty switch use part number K508A...

$12.58

Item # K508

Commutator Stone, 1/4 x 1/2

Brush seater/commutator stone. To seat new brushes, run this stone over the surface of the commutator with the motor running. The abrasive from the stone will stick to the commutator, wearing down the brushes to match the shape of the commutator. Clean the commutator with compressed air to remove the abrasive when done...

$10.30 - $11.44

Item # SW05

Switch, Med duty 20 Amp

On-Off toggle switches for Floor Sanding edgers. These are a 2-pole switch. Medium duty 20 amp @110v This is the edger switch we recommend for most Clarke Edgers S7 (Super 7R) & B2..

$14.28

Item # K508A

115v Bulb 25W

Standard heavy duty bulb for 110v Clarke type edgers. 25 watt See our part number E13L for our replacement LED bulb that will not not burn out and is a direct replacement without any modifications. We also have part number E26 that is a brighter pod LED light upgrade kit...

$1.83

Item # E13

Bag Clamp

This quick release bag clamp makes removing & reattaching dust bags easier on sanders. The clamp when fully expanded has a diameter of 4 inches. Colors may vary...

$21.00

Item # SN001

Bearing, Sealed*

The caster pivot bearings on Super 7 edgers. These have a teflon seal to keep dust out. Also fits the edger wheel...

$5.18

Item # CE67

Brushes OS no wire, set of 4

Replacement brushes for Super 7 edgers. Set of 4 brushes without wires (for brushes with wires, see part #CE57). We recommend replacing brushes when they are worn down to 2/3 the normal length. Running brushes shorter than this can cause the armature to wear faster. Carbons measure 3/16 x 15/16, 7/8 long...

$18.84

Item # CE09

Brushes w/wire, 4per set Super7*

Replacement brush set for Clarke Super 7 / 7R edgers. Set of 4 brushes with wires (for brushes without wires, see part #CE09). We recommend replacing brushes when they are worn down to 2/3 the normal length. Running brushes shorter than this can cause the armature to wear faster. Carbons measure 3/16 x 15/16, 7/8 long. Made in USA by the original Clarke manufacturer. Replaces OEM part number 40818A..

$18.50

Item # CE57

Brushes, set of 2

Set of 2 replacement brushes for Super 7 2-brush edgers. Note that most Super 7 edgers are 4-brush, make sure that you confirm which you need before ordering. We recommend replacing brushes when they are worn down to 2/3 the normal length. Running brushes shorter than this can cause the armature to wear faster. Carbons measure 5/16 x 5/8, 1 inch long...

$23.94

Item # CE04

Caster Super 7 Edger^

Floor Sanding Edger Caster Wheel Assembly for Clarke Super 7R Edger. Original factory type design type wheel assembly with steel wheel. Upgraded with a grade 5 stud and a lock nut to stop the assembly from loosening up and falling off. Upgraded sealed electric motor quality wheel bearings. We also have a wheel bracket upgrade kit to convert to larger rubber wheels. See part # CE99..

$25.00

Item # CE05

Caster, Urethane OEM

Original factory wheel assembly with Urethane wheel from Clarke. Softer than steel to reduce wheel marks. Non-marking urethane material over steel core. V shaped urethane wheel. (this is kind of a pointed tire) See our EZ Roll Wheel Kit #CE99 for larger rubber wheels on billet polished brackets for soft floors or everyday use...

$59.78

Item # CE05U

Discharge Pipe, Swivel w/bag

These swivel pipes are ideal for dust collection. They can be connected to a 1.5 hose, a 2 hose or a bag. Kit includes Dust pipe, Bag and rubber reducer. Fits Super 7 edgers...

$238.56

Item # CE72N

Dust Skirt Velcro S7

These skirts close up the gap between the edger and the floor, improving dust pickup. This is 3 short pieces, to go between the wheels. Fits Super 7 edger. Clean aluminum with a thinner before applying the adhesive Velcro. For best results apply the night before the edger will be used to allow adhesive to bond...

$11.35

Item # CE75

Edger Lube

This is our special grease mixture. The grease used by most manufacturers is too thick to flow into the gears. This mixture is thin enough to flow, but thick enough not to leak past the seals. Please note this may be blue or red...

$11.03

Item # KEL1

Edger Lube, Gallon~

This is our special grease mixture. The grease used by most manufacturers is too thick to flow into the gears. This mixture is thin enough to flow, but thick enough not to leak past the seals...

$195.83

Item # KEL1G

Edger Wrench 9/16 Inch

Paper wrench for Clarke Super 7R edger. For removing the paper bolt on Super 7 edgers. 9/16� hex, fits a 3/8 bolt head. Replaces OEM number 987300..

$15.54

Item # CE14

Latch, Edger Case (old)

Replacement latch for older Super 7 & B-2 edger cases. This is a single latch, some cases have 2, some cases have 4. For new style cases with metal latches, order E06...

$13.42

Item # E05

Paper Screw

Replacement paper retainer bolt for Super 7 Edger. Thin head, OEM size. This bolt does not have a hole for a cotter pin � if you need the hole, order part #CE58US...

$1.75

Item # CE11

S7 Caster Upgrade EZ Roll Rubber

The EZ Roll kit retrofits your edger with 1-5/8 diameter grey wheels. Not only do these roll better, they provide a little wider wheel base for improved stability. The soft rubber wheels work excellent on softer woods like pine. This kit fits the Super 7 edger. Our best kit for soft floors. Highly Polished Aluminum brackets. Made in USA Easy wheel adjustment. No modifications to edger. Easily switch between factory wheels and this kit. Replacement wheel assembly part number is CE98 (2 Required per edger) CE98 Replacement Wheel Assembly AV06 Replacement Tire Only..

$115.00

Item # CE99

Vac Attachment Old Style1.25^

Adapter kit for connecting your Super 7, Essex Silver Line SL7, or KT Blizzard edger to a 1.5 inch vacuum hose. Designed for the old style (fixed) pipe. Also includes coupling to connect two 1.5 inch hoses for more length...

$19.00

Item # CE72