Nilfisk 17SD

Complete parts breakdown for Nilfisk 17SD
This Parts breakdown is for the following machines:

17in Pacesetter SD buffer- UFO

Related Products

Stain Carpet Pad 16 in.

16 in. Carpet Pad for use with your Floor Sanding Buffer. All pads are vacuumed and heat singed on the edge. If you are driving this carpet with a maintenance pad and it slips out you may want to use a spray glue to stick the two together. The spray glue can easily be peeled apart when finished. With a loose pad on a flat surface, pour 6 oz of stain into the center, spirally out from center. quickly place carpet side of the pad on floor and set buffer on top and start buffing immediately. Note: For use on the Spin Coater, order part number B10 (pad with center hole)..

$5.60

Item # B09

LED Light Kit, Buffer US

This light is intended to bolt to the top cover of buffers. 20 watt draw gives 120 watt equivalent 1600 lumens Bracket comes with hardware to mount to the three existing screws on the top of the buffer motor or hardware and spacer to drill one 1/4 inch hole on the buffer motor top shroud and mount it with the included knob and spacer. Note: This light does not run on 240 volt power, for 240 volt buffers use B27 instead. Includes: LED Light, 3-way power splitter, spacer block & mounting hardware. In order to use on the ZBUS Buffers, you must change the plugs on the buffer motor (6266 & 6269)..

$89.51

Item # B26

Skirt Kit, 16-17in w/ Vac Assy^

Convert your 16-17 inch buffer to a DCS Buffer. Full kit with everything you need. Heavy Duty skirt Sewn to brush material. Kit includes: Skirt (B25), fitting to connect to buffer (B22), hose (VH01) and mount to clamp on handle (B21). Skirt clamps around housing of buffer with a worm drive clamp...

$167.14

Item # B25A

Arm Link, Left

$14.96

Item # BR20

Arm Link, Right

$14.52

Item # BR18

Bumper 16 inch

$35.14

Item # BR34

Capacitor, Run 50mfd*

Run capacitor used primarily on Galaxy Floor Sanders (2000, Omega, BD12, B12). Also used on American Sanders RS16 & RS16DC buffers and Nilfisk 17SD Buffers.

$25.00

Item # GAL032

Capacitor, Start 340-408mfd

$17.04

Item # B03

Coupling Heavy Duty Buffer

Heavy Duty coupling for Buffers Used between the motor armature and gearbox. Original on some buffers and universal upgrade for most buffers with the rubberized coupling. Used with buffers that are sanding with a hard plate or with the UFO. Sometime called the shear pin. Fits almost all floor buffers with 3/4hp, 1hp, 1-1/2hp motors including: American Sanders RS 16TH, RS16DC, Sander 1600, Sander 1600DC, Sander 16, Mastercraft, Mercury, Bona, Clarke, Advance, Nilfisk, Hawk, etc. Does not fit FM series buffers - use BF06 instead

$35.00

Item # B01

Cover, Motor

$53.02

Item # BR30

Gearbox, 10-1

$850.00

Item # BN12

Handle Clamp Assy

$80.04

Item # BN19

Handle Tube

$50.96

Item # BR38

Handle, Back

$36.80

Item # BN01

Handle, Front

$70.42

Item # BN02

Hardware Kit

$148.36

Item # BN04

Main Frame

$122.67

Item # BR33

Motor

$966.00

Item # BN29

Shield, non-DC

$245.00

Item # BR37

Start Switch

This start switch is found under the top motor cover on RS16 buffers. This controls the start capacitor, disconnecting once the motor is running. When they fail, the motor will struggle to start and trip breakers. This can be replaced with the BN70 electronic start switch.

$41.58

Item # BR66

Switch Lever Kit

$140.44

Item # BN03

Switch, On/Off

$16.22

Item # BN05

Wheel Kit

$178.00

Item # BN24

The following documents are also available for this machine:

Machine Manual

Wiring Diagram (original)

Wiring Diagram (upgrade)