16 in. Carpet Pad for use with your Floor Sanding Buffer. All pads are vacuumed and heat singed on the edge. If you are driving this carpet with a maintenance pad and it slips out you may want to use a spray glue to stick the two together. The spray glue can easily be peeled apart when finished. With a loose pad on a flat surface, pour 6 oz of stain into the center, spirally out from center. quickly place carpet side of the pad on floor and set buffer on top and start buffing immediately. Note: For use on the Spin Coater, order part number B10 (pad with center hole)..
$5.60
Item # B09
This light is intended to bolt to the top cover of buffers. 20 watt draw gives 120 watt equivalent 1600 lumens Bracket comes with hardware to mount to the three existing screws on the top of the buffer motor or hardware and spacer to drill one 1/4 inch hole on the buffer motor top shroud and mount it with the included knob and spacer. Note: This light does not run on 240 volt power, for 240 volt buffers use B27 instead. Includes: LED Light, 3-way power splitter, spacer block & mounting hardware. In order to use on the ZBUS Buffers, you must change the plugs on the buffer motor (6266 & 6269)..
$75.00
Item # B26
Convert your 16-17 inch buffer to a DCS Buffer. Full kit with everything you need. Heavy Duty skirt Sewn to brush material. Kit includes: Skirt (B25), fitting to connect to buffer (B22), hose (VH01) and mount to clamp on handle (B21). Skirt clamps around housing of buffer with a worm drive clamp...
$163.51
Item # B25A
Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.
$7.00
Item # 6002
Item # 6202
$27.50
Item # BS68
$60.00
Item # BS67
$7.03
Item # BS18
$13.45
Item # BA55
$27.00
Item # AS73
$15.18
Item # B03
$46.74
Item # BS16
$14.63
Item # OB39
Original rubber type buffer coupling for buffers. Used between the motor armature and gearbox. Upgrade to the #B01 for a more heavy duty coupling for hard plating or use with the UFO.
$38.22
Item # B02
$114.94
Item # BR06
$69.16
Item # BR02
$5.89
Item # BS02
$78.47
Item # BS01
$6.27
Item # BS09
Aluminum on off lever for Sander 16 left or right
$19.03
Item # BS11
Tab load spring. For 6202 bearing.
$2.25
Item # SPR1128
$1.00
Item # XEEH
Item # XEBH
Item # XEBG
Item # XIBDG
$42.75
Item # BS26
Item # DJF27
Item # XACFF
Item # XAAFG
Item # XAAGG
Item # XAAGK
Item # XABDC
Item # XABDG
Item # XABBG
Item # XABCA
$3.00
Item # XALHE
Item # XAQDG
$120.64
Item # BA35
$26.62
Item # B06
$55.00
Item # BM15
Item # BS40
Replacement inserts also available - see CE56 and AE62.
$22.00
Item # CE55
Switch measures 1.75 x 1.25 x 5/8 with plunger almost in middle between mounting holes which are 1 inch apart. Used on Clarke
$20.90
Item # BS05
$22.96
Item # BS06
$98.12
Item # BR03
$6.99
Item # BA22
Item # XOAG
Item # XODD
Item # XODG
Item # XOEJ
Item # XOBH
$22.29
Item # BS21
$11.62
Item # BS24
Here are a few tips on using them.
