16 in. Carpet Pad for use with your Floor Sanding Buffer. All pads are vacuumed and heat singed on the edge. If you are driving this carpet with a maintenance pad and it slips out you may want to use a spray glue to stick the two together. The spray glue can easily be peeled apart when finished. With a loose pad on a flat surface, pour 6 oz of stain into the center, spirally out from center. quickly place carpet side of the pad on floor and set buffer on top and start buffing immediately. Note: For use on the Spin Coater, order part number B10 (pad with center hole)..
$5.60
Item # B09
This light is intended to bolt to the top cover of buffers. 20 watt draw gives 120 watt equivalent 1600 lumens Bracket comes with hardware to mount to the three existing screws on the top of the buffer motor or hardware and spacer to drill one 1/4 inch hole on the buffer motor top shroud and mount it with the included knob and spacer. Note: This light does not run on 240 volt power, for 240 volt buffers use B27 instead. Includes: LED Light, 3-way power splitter, spacer block & mounting hardware. In order to use on the ZBUS Buffers, you must change the plugs on the buffer motor (6266 & 6269)..
$75.00
Item # B26
Convert your 16-17 inch buffer to a DCS Buffer. Full kit with everything you need. Heavy Duty skirt Sewn to brush material. Kit includes: Skirt (B25), fitting to connect to buffer (B22), hose (VH01) and mount to clamp on handle (B21). Skirt clamps around housing of buffer with a worm drive clamp...
$170.51
Item # B25A
Electronic start switch used on EZ8 sanders and some buffers. This switch controls the start capacitors.
$110.00
Item # EZ70
NEMA 5-15 15 amp 125 volt 3-prong grounding male plug. This is the standard household plug. Eaton Cooper Arrow Hart Brand
$15.85
Item # 6266
Replacement Buffer Dust Skirt. Heavy Duty skirt Sewn to brush material. Buffer dust skirt for 15-17 inch buffers. Clamps around housing of buffer with a worm drive clamp. Includes clamp.
$109.30
Item # B25
Replacement nut for B22 fitting. Thin nut for low profile use under the buffer frame.
$3.00
Item # B23
$144.16
Item # BC36
$108.62
Item # BC34
$193.44
Item # BC30
$20.85
Item # BC31
$22.00
Item # BA56
$13.74
Item # BA63
$93.82
Item # BC17
$174.24
Item # BC27
Buffer frame dust collection fitting / adapter barb. This fitting is intended to go in a 2 hole drilled in the buffer shroud/frame. 1-1/2 vacuum hose fitting. Comes with 2 nuts.
$15.00
Item # B22
$630.00
Item # BC13
$33.38
Item # BC18
$68.84
Item # BC19
$12.82
Item # BC04
$13.25
Item # BC01
$204.12
Item # BC38
$113.12
Item # BC21
$50.38
Item # BC05
$30.00
Item # BC14
$40.01
Item # BC10
$38.58
Item # BC09
$1.00
Item # XEAJ
Item # XEJH
$2.00
Item # XEKD
$21.74
Item # BC22
Item # XAKGM
Item # XAODF
Item # XAODJ
Item # XAAFG
Item # XABFD
Item # XANDC
Item # XAHFC
Item # XATDC
$355.73
Item # BC03
Item # XODF
Item # XOBF
Item # XOBG
Item # XOFJ
$54.82
Item # BC24
Wide wheel for Ceno Extreme buffers. Wheel is 5 x 2
$47.10
Item # BC25
Here are a few tips on using them.
