This Parts breakdown is for the following machines:
Clarke no longer sells this part; this is an aftermarket plastic version. Comes with CL86 latch.
$150.00
Item # AP90
Electronic start switch similar to the CL38 Sinpac switch. Can be used to replace the CL38. The case size is smaller (1-3/8 inch diameter x 2-3/4 inch long), and the terminals are in a different order (3 2 4 1). When installing, be sure to connect the wires to the correct terminal number. See install video: https://youtu.be/Ul21bGRjl_I
$165.00
Item # CL38B
These 2-pole circuit breaker switches are used on most Clarke/Alto sanders. This is 30 amp with push connect terminals, standard for most machines.
$78.00
Item # K840
NEMA L6-20 20 amp 250 volt grounding twist-lock male flanged inlet. This is the standard size used on the Hummel & Clarke/Alto machines. Eaton Cooper Arrow Hart Brand
$17.12
Item # 6215
3L Series belt. These are commonly used for fans on large sanders or to drive the pads on radiator edgers. 3/8 Wide x 7/32 thick.
$8.00
Item # 3L270
3VX Series belt. These are the type that fit most modern machines. 3/8 wide x 5/16 thick cogged.
$14.00
Item # 3VX375
Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.
$7.00
Item # 6000
$31.00
Item # 6010
$36.00
Item # 6011
$13.95
Item # 6202-10
Item # 6202
$11.00
Item # 6302
$58.80
Item # CL21
$41.33
Item # AP15
$28.42
Item # AS17
$54.88
Item # 51190A
$57.54
Item # CL100
$15.00
Item # CL60
$52.00
Item # AP07
$3.00
Item # AP27
$84.59
Item # AS62
$22.00
Item # CL40
Start Capacitor (plastic) two required for Baldor motors used on the Clarke Apollo 8, Clarke Classic 8, Clarke Floorcrafter, Clarke American 8 (3450 RPM)
$18.50
Item # CL39
$200.10
Item # CL23
$5.60
Item # AS151
$160.30
Item # AS87
$20.90
Item # AS34
Edge guide/cone roller for the Hummel Sander. Assembled with bearings, threaded stud, and nut. Replacement bearings for this roller is # 626 OEM roller available under part # HS108
$65.00
Item # HS21
$39.24
Item # AP45
$47.41
Item # FC103
$288.12
Item # AS61
$6.49
Item # S37
$46.06
Item # AP34
$125.91
Item # AP24
Motor fan cover for 4hp Baldor motors on Clarke sanders. Fits Apollo, Clasic, Floorcrafter and newer American 8 & 12 sanders.
$63.21
Item # CL144
$95.00
Item # CL52
$35.00
Item # AS59
$116.20
Item # AS57
$68.38
Item # CL145
Item # AP30
$8.40
Item # AS81
This is a set of 2 pieces, one for each side of the handle.
$23.25
Item # CL35
$36.10
Item # AP38
$67.32
Item # CL34
$1.00
Item # XMCO
$2.00
Item # XMCZ
$12.00
Item # CL67
$62.00
Item # CL63
Item # XKCFD
Item # XKCFH
Item # XKABD
$19.95
Item # CL75
$7.50
Item # CL07
$41.01
Item # CL86
$29.50
Item # CL92
$63.00
Item # AP20
Item # XGAI
$28.15
Item # AP18
Item # XPAL
$1,078.01
Item # AS101B3
Item # XESH
Item # XETH
Item # XEAJ
Item # XEDJ
Item # XEMF
Item # XEMH
Item # XELH
Item # XEBF
Item # XEBD
Item # XEBM
Item # XEBH
Item # XEBG
Item # XEZM
$50.63
Item # CL46
$9.00
Item # CL132
$1.25
Item # CL131
Item # XIEFF
Item # XIDAD
Item # AP06
$30.37
Item # AS33
$278.53
Item # AP13
Item # AS25
Item # XMDF
Recovered 8 Clarke Apollo 8 drum. This drum has been tapered (football shaped) to assist in tracking and reduction of edge cutting. Precision balanced to similar specs as all our belt sander drums. These drums are not exchanged as good cores are difficult to keep in house. There are 2 different Cores used on Apollo sanders. The standard is a Aluminum core and the other is a steel core from a Classic 8. Because of this we recover your core only.
$310.00
Item # RAP8
$16.02
Item # CL12
$5.20
Item # CL18
Item # CL42
$3.50
Item # CL139
$21.40
Item # AP09
$8.53
Item # AS86
$4.00
Item # AP08
$37.75
Item # AP43
Item # AP44
$202.67
Item # CL135
Item # XAFFD
Item # XAIHD
Item # XAAFI
Item # XAAFJ
Item # XAAHF
Item # XAAHG
Item # XAAHH
Item # XAAHI
Item # XAAGG
Item # XAAGJ
Item # XAAGM
Item # XAAKM
Item # XABFD
Item # XABFG
Item # XABDD
Item # XABDG
Item # XABBB
Item # XABBC
Item # XABCD
$6.00
Item # XALJE
Item # XALFA
Item # XALFG
Item # XALHH
$5.00
Item # XALHN
Item # XAEHF
Item # XAEHG
$24.00
Item # CL29
$7.51
Item # AP39
$7.41
Item # AP14
$11.66
Item # AS84
$26.60
Item # CL24
$28.80
Item # CL30
$9.75
Item # CL68
$296.94
Item # CL122
$203.56
Item # AS103
$30.00
Item # CL77
$405.95
Item # AP28
$1,003.01
Item # AP146
$8.25
Item # CL59
Item # AP21
$4.75
Item # CL124
Item # XOAM
Item # XOAH
Item # XOAI
Item # XOEF
Item # XOED
Item # XOBD
Item # XOFG
Item # AS157
Side wheels made from a red urethane bonded to a metal core. Wheels come with bearings & axles. 3-1/2 diameter, fit Classic 8, Classic 12 and Apollo 8 belt sanders. (Back wheel is part #CL118)
$72.61
Item # CL01
Double rear wheels made from a red urethane bonded to a metal core. Wheels come with bearings & spacers. 3-1/2 diameter, fit Classic 8, Classic 12 and Apollo 8 belt sanders. (Side wheel is part #CL01)
$124.00
Item # CL118
$36.61
Item # AS35
The following documents are also available for this machine:
Here are a few tips on using them.