US Sander

Pulley, Motor

..

$192.00

Item # AS13

Pulley, Motor, Large Bore

..

$179.00

Item # AS250L

Pulley, Motor, Large Bore*

..

$190.00

Item # AS13L

Pulley, Motor, Prosand 10

Fits the Leeson motor. For the Cobra 10 motor, use WS214B. This fits a 1-1/8" shaft, the keyway is 1/4", and the pulley diameter is 3-7/8"..

$286.00

Item # WS214C

Pulley, Motor, Prosand 8

Fits the Leeson motor. For the Cobra 8 motor, use WS214. This fits a 1-1/8" shaft, the keyway is 8mm (5/16"), and the pulley diameter is 4-5/16". This is a modified version of the WS214 pulley, so it will be slightly larger diameter than the original pulley. Comes with a special stepped key to fit the 1/4 keyway on the Leeson motor, and a spacer. Install the pulley on the motor first, then the spacer...

$290.32

Item # WS214B

Pulley, Motor, Std 8

..

$180.00

Item # AS250

Pulley, Motor~

..

$92.00

Item # CK21

Pulley, Single Groove, 12

..

$93.00

Item # AS150A

Push cap, 1/2

..

$1.00

Item # DJF21

push cap, 1/2

..

$2.00

Item # XMDJ

push cap, 1/4

..

$1.00

Item # XMDF

push cap, 5/16

..

$1.00

Item # XMDG

push cap, 5/8

..

$2.00

Item # XMDL

Rear Wheel Assy Urethane 504*

Rear wheel made from a red urethane bonded to a metal core. Comes with bearings, spacers & axle. 3-1/2 diameter, fits Clarke or Porter Cable 12, 504, and F89 drum sanders. (Side wheel is part #CS01)..

$105.71

Item # CS56

Rear Wheel Complete w/Yoke

Rear wheel with yoke for Hummel This is the new style wheel with the new style single yoke caster...

$352.89

Item # HS091

Rear Wheel Shaft

..

$14.62

Item # GAL065

Rear Wheel Tire

..

$35.25

Item # TS02

Rebuilt Galaxy Motor~

Rewound motor with new capacitors and start switch. This is an exchange or rebuild of your motor - we must have your old motor prior to shipping. The motor we have in stock is 7.5 hp, if your motor is an older 4 hp we cannot exchange, we will have to rebuild your motor. Typical turnaround time on rebuilding your motor is 3-4 weeks...

$2,200.00

Item # GAL012RB

Rebuilt Hum Mtr w/ Ctrl Box^

Hummel motors will burn up with low voltage. This is why we recommend running no longer than a 75 foot cord without a power booster. However, if your motor does burn up, we have these rewound motors. These are available by exchange only - we must get a rewindable motor in exchange...

$2,115.94

Item # HSMRTB

Recovery KT8 / Bona HD Belt Drum

Recovered 8 KT Taurus - NT8 Kunzle and Tasin 8 drum. This drum has been tapered (football shaped) to assist in tracking and reduction of edge cutting. Precision balanced to similar specs as all our belt sander drums...

$360.00

Item # RTS8

Recovery of Amer 12 Tin End Drum

We recover your old American 12 tin end covered drum by vulcanizing red rubber,grinding to size (7.25) and mechanically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service...

$400.00

Item # RAS12T

Recovery of American 12 Drum

We recover your American 12 drum by vulcanizing red rubber,grinding to size (7.25) and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We can rebush the drum shaft holes as an extra service when needed and approved. All drums molded in house for a superior bond. Great for Rider use. Recover takes about two weeks, sometimes longer or shorter depending on demand...

$400.00

Item # RAS12

Recovery of American 8 Drum

We recover your American 8 drum by vulcanizing red rubber,grinding to size (7.25) and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service...

$360.00

Item # RAS8

Recovery of Apollo 8 Drum

Recovered 8 Clarke Apollo 8 drum. This drum has been tapered (football shaped) to assist in tracking and reduction of edge cutting. Precision balanced to similar specs as all our belt sander drums. These drums are not exchanged as good cores are difficult to keep in house. There are 2 different Cores used on Apollo sanders. The standard is a Aluminum core and the other is a steel core from a Classic 8. Because of this we recover your core only...

$360.00

Item # RAP8

Recovery of Bona Belt 10 Drum

..

$405.00

Item # RBB10

Recovery of Bona Belt 8 Drum

Recovered 8 BONA BELT 8 drum. This is not an older Bona prosand drum!This drum has been tapered (football shaped) to assist in tracking and reduction of edge cutting. Precision balanced to similar specs as all our belt sander drums...

$360.00

Item # RBB8

Recovery of Clarke 504 Drum

We recover your Old CLARKE (not Clarke American) 504 with screw adjustable clamps 8 drum by vulcanizing red rubber,grinding to size (7 3/8) and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service...

$360.00

Item # RCS504

Recovery of Clarke CF12 Drum

We recover your Old CLARKE (not Clarke American) CF12 12 drum by vulcanizing red rubber,grinding to size (7 3/8) and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service...

$400.00

Item # RCS12

Recovery of Clarke F89 Drum

We recover your Old CLARKE (not Clarke American) F89 by vulcanizing red rubber,grinding to size and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service...

$360.00

Item # RCSF89

Recovery of Classic 12 Drum

We send this drum to an outside source. Add additional 3-4 weeks...

$450.00

Item # RCL12