Switch, On/Off, Aftermarket

Replacement switch for Galaxy sanders. Fits machines built before May 2010. This switch is slightly smaller than the original, but has the same rating. Note: wiring on switch may be different than some older switches - see wiring instructions with switch

$75.00

Item # GAL163A

Bearing, Ball, 6202-2RSH C3

Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.

$7.00

Item # 6202

Bearing, Ball, 6204-2RS

Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.

$9.00

Item # 6204

Switch 110/220

This is the 3-position, snap action switch used for the 110-220 selector switch on many of the older drum sanders.

$180.00

Item # K280

Axle Assembly

$32.00

Item # CS31

Bearing Retainer Ring, F89

$32.00

Item # CS40

Bearing, Ball, W204PP

W200 Series bearings are similar to a 6200 series bearing, only wider. They may have rubber seals or steel shields. Most commonly used on some of the older Clarke & Portercable drum sander motors.

$57.67

Item # W204PP

Bearing, Chasis F89, PC10

$22.00

Item # CS29

Bracket, Pressure Lever

$24.54

Item # GAL120

Brushes, Master, set of 2 pair

Carbons measure 1/4 x 7/8, 1-1/4 inch long. These have a wire connecting 2 brushes to make a pair; contains 2 pairs (for brushes total). Fits the Master motor on some of the older Clarke and Porter Cable drum sanders.

$35.00

Item # CS46

Brushes, Motor set of 2 pairs

Motor Brush set. Includes 4 carbon brushes with two connected by a wire. Fits most Peerless Sander motors 1.5, 2, and 3 HP ie American Standard 8, Clarke American Super 8, Clarke 504 etc see diagram listing below for some of the sanders these are used on. Carbons measure 1/4 x 5/8, 1-1/4 inch long. These have a wire connecting 2 brushes to make a pair; contains 2 pairs (4 brushes total). Fits the Peerless motor on most of the older drum sanders.

$32.15

Item # S25

Brushes, Motor, set of 2 pairs

Carbons measure 1/4 x 1/2, 1-1/4 inch long. These have a wire connecting 2 brushes to make a pair; contains 2 pairs (for brushes total). Fits the motor on some of the older Clarke and Porter Cable drum sanders.

$30.56

Item # CS42

Bumper F89 & 504

$17.19

Item # CS144

Cable Bracket Assy incl GAL070

$62.57

Item # GAL069

Carry Handles Set 504 CF12 F89

For carrying Clarke (not American) sanders up and down stairs. Fit Clarke & Porter cable 12, Clarke 504 & F89, Portercable F87 & F89, and Galaxy 506 drum sanders.

$91.51

Item # CS12

Chassis Fulcrum

$22.00

Item # CS63

Clip, Side Cover

$20.90

Item # AS34

Collar Long Rear Wheel

$5.70

Item # GAL125

Collar Short Rear Wheel

$5.70

Item # GAL124

Control Rod

$24.95

Item # CS71

Control Rod Fork

$29.00

Item # CS08

Drum Arm Washer, F89

$19.95

Item # CS83

Drum Pulley 6 inch

$275.00

Item # CS48-6

Drum Shaft F89

$179.90

Item # CS16

Dust Pan F89

$110.00

Item # CS26

Dust Pipe

$50.00

Item # CS91

Elbow

$308.88

Item # CS92

Fan Plate

$125.00

Item # CS94

Fan Pulley 8 inch machine only

$50.00

Item # CS24

Fan Shaft, F89

$45.00

Item # CS45

Fork Pin

$1.50

Item # CS09

Handle Pipe

$39.95

Item # CS80

Handle Stud

$9.00

Item # CS54

Handle, Control

Replacement handle for Galaxy sanders. For a lower cost heavy duty alternative, see GAL092A.

$78.74

Item # GAL092

Idler Arm

$45.00

Item # CS21

Idler Pulley

$51.33

Item # CS22

Idler Pulley Shaft

$28.00

Item # CS49

Lever Stud

$12.95

Item # CS138

Motor Mount Pin

$27.00

Item # CS06

Motor Screw F89, 3/8-16 x 3

$19.43

Item # CS03

Nut & Washer

$2.50

Item # CS47

Pigtail Assembly 20 amp^

To replace the inlet found on many of the older drum sanders. This pigtail has a plate that uses the same mounting holes as the old inlet, and a 6212 (20 amp twist-lock) plug.

$29.56

Item # CS142

Pipe Support

$130.00

Item # CS93

Pivot Bolt*

Rear wheel yoke pivot shaft for Galaxy, Clarke 504, Clarke F89, and Porter Cable F87. When the rear caster does not swivel smoothly there is a good chance that this shaft is bent.

$35.00

Item # CS37

Plate, Pressure Control

$38.88

Item # GAL087

Pulley, Motor*

$250.00

Item # CS51

Rear Wheel Assy Urethane 504*

Rear wheel made from a red urethane bonded to a metal core. Comes with bearings, spacers & axle. 3-1/2 diameter, fits Clarke or Porter Cable 12, 504, and F89 drum sanders. (Side wheel is part #CS01)

$105.71

Item # CS56

Recovery of Clarke F89 Drum

We recover your Old CLARKE (not Clarke American) F89 by vulcanizing red rubber,grinding to size and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service.

$360.00

Item # RCSF89

Retainer, Bearing (CS96)*

$5.60

Item # AS86

Rod, Cable Support

$60.21

Item # GAL068

Rubber Washer (set of 2)

$8.95

Item # CS10

Screw, socket, 10-24 x 0.625

$1.00

Item # XAEDE

Screw, Wing

$2.00

Item # CS118A

Seal Bearing Dust

$8.59

Item # GAL110

Seal, Caster*

$14.28

Item # CS38

Shock 2 per set, F89

$10.95

Item # CS28

Side Cover Screw

$11.00

Item # CS57

Side Wheel Axle

$22.50

Item # CS17

Side Wheel Spacer

$8.50

Item # CS77

Spacer

$8.00

Item # CS127

Spacer, Fan Collar F89/504

$9.84

Item # CS73

Spring, Idler

$12.96

Item # CS43

Spring, Pressure Control OEM

$35.05

Item # GAL134

Switch, Rotary Conversion Kit^

Replaces the old rotary switch on Clarke & Portercable drum sanders. Includes a 30 amp circuit breaker switch (K840), adapter housing, and mounting hardware.

$139.80

Item # CS50

Template F89

Paper templates make it easier to cut the paper to fit your machine. Use the angle cut on the end of the template to get a perfect bend. These have a fixed length, so you may need to cut the paper a little longer or shorter to fit your machine. Fits Clarke & Porter Cable F89.

$30.00

Item # CS124

Tension Lever GAL119

$55.38

Item # CS34

Wheel, Red w/bearings*

These wheels are made from a red urethane bonded to a Aluminum core and come with bearings installed. Upgraded version now fits old and new style American 8(Super 8 / Standard 8), American 12, Clarke/Portercable F89, 504 and CF12. The wheel comes with two thick and one thin spacer. When used on older American 8 (Super 8 / Standard 8) or American 12 with the long old style wheel axle use one thick washer on each side of the wheel. When used on newer American 8 or American 12 with the shorter new style wheel axle use one thin washer on the inside of the wheel. When used on Clarke / Porter Cable F89, 504 and CF12 use one thin washer on the inside of the wheel.

$60.00

Item # AS01

Wooden Handle

$70.90

Item # CS02

Yoke*

$100.13

Item # CS95