NEMA L6-30 30 amp 250 volt grounding twist-lock male flanged inlet. This is the standard size used on KT & Galaxy machines. Eaton Cooper Arrow Hart Brand
$37.60
Item # 6345
Sealed ball bearing. Commonly found on sanders, buffers and edgers. If you are not sure what bearing you need, see the parts diagram for your machine.
$7.00
Item # 6202
$12.00
Item # 6205
These blade style switches have a high current rating for starting and stopping motors. This 30 amp switch fits most of the older drum sanders, including the F89, 504 and Silverline Pro 8.
$122.72
Item # K309
This is the 3-position, snap action switch used for the 110-220 selector switch on many of the older drum sanders.
$208.44
Item # K280
$196.44
Item # CS134
$277.47
Item # GAL308
$32.00
Item # CS31
$27.09
Item # CS18
Similar to a 6203, but the inner race on the bearing sticks out on one side. See the bearing size chart for more information.
$14.10
Item # 87503
W200 Series bearings are similar to a 6200 series bearing, only wider. They may have rubber seals or steel shields. Most commonly used on some of the older Clarke & Portercable drum sander motors.
$48.00
Item # W205PP
$23.00
Item # CS30
$103.09
Item # GAL075
$24.54
Item # GAL120
Carbons measure 1/4 x 7/8, 1-1/4 inch long. These have a wire connecting 2 brushes to make a pair; contains 2 pairs (for brushes total). Fits the Master motor on some of the older Clarke and Porter Cable drum sanders.
$21.28
Item # CS46
Motor Brush set. Includes 4 carbon brushes with two connected by a wire. Fits most Peerless Sander motors 1.5, 2, and 3 HP ie American Standard 8, Clarke American Super 8, Clarke 504 etc see diagram listing below for some of the sanders these are used on. Carbons measure 1/4 x 5/8, 1-1/4 inch long. These have a wire connecting 2 brushes to make a pair; contains 2 pairs (4 brushes total). Fits the Peerless motor on most of the older drum sanders.
$17.75
Item # S25
Carbons measure 1/4 x 1/2, 1-1/4 inch long. These have a wire connecting 2 brushes to make a pair; contains 2 pairs (for brushes total). Fits the motor on some of the older Clarke and Porter Cable drum sanders.
$30.56
Item # CS42
$60.91
Item # CS144
$85.47
Item # CS145
$62.57
Item # GAL069
For carrying Clarke (not American) sanders up and down stairs. Fit Clarke & Porter cable 12, Clarke 504 & F89, Portercable F87 & F89, and Galaxy 506 drum sanders.
$67.51
Item # CS12
$250.00
Item # CS119
$180.00
Item # CS106
$20.90
Item # AS34
$5.70
Item # GAL125
Item # GAL124
$24.95
Item # CS71
$29.00
Item # CS08
$184.47
Item # CS128
$19.95
Item # CS84
$22.00
Item # CS90
$140.00
Item # CS58-6
$150.00
Item # CS61
$217.72
Item # CS15
$9.96
Item # CS76
$231.52
Item # GAL108
$120.00
Item # CS129
$75.00
Item # CS78
$163.65
Item # GAL071
$244.13
Item # GAL112
$12.50
Item # CS60
$50.00
Item # CS62
Item # CS24
Item # CS23
$74.00
Item # CS59
$1.50
Item # CS09
$26.50
Item # CS74
$9.00
Item # CS54
$78.74
Item # GAL092
$292.95
Item # GAL312
$45.00
Item # CS21
$55.17
Item # CS22
$28.00
Item # CS49
$12.95
Item # CS138
Item # CS35
$2.00
Item # CS20
Rear wheel yoke pivot shaft for Galaxy, Clarke 504, Clarke F89, and Porter Cable F87. When the rear caster does not swivel smoothly there is a good chance that this shaft is bent.
$35.00
Item # CS37
$52.26
Item # GAL087
$14.00
Item # CS105
2 groove aluminum drum pulley for Clarke 504, Porter Cable F87. Does not fit the CF12 with single groove pulleys.
Item # CS14
$350.00
Item # CS13
Rear wheel made from a red urethane bonded to a metal core. Comes with bearings, spacers & axle. 3-1/2 diameter, fits Clarke or Porter Cable 12, 504, and F89 drum sanders. (Side wheel is part #CS01)
$107.92
Item # CS56
We recover your Old CLARKE (not Clarke American) 504 with screw adjustable clamps 8 drum by vulcanizing red rubber,grinding to size (7 3/8) and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service.
$310.00
Item # RCS504
We recover your Old CLARKE (not Clarke American) CF12 12 drum by vulcanizing red rubber,grinding to size (7 3/8) and electronically balancing. Drum bushings must be in good condition to do balancing and precision grinding. We do drum bushings as an extra service.
Item # RCS12
$8.53
Item # AS86
$60.21
Item # GAL068
$8.95
Item # CS53
$14.54
Item # CS04
$1.00
Item # XAEFF
Item # XAEHG
Item # XAEHH
Item # XAEII
$8.59
Item # GAL110
$10.60
Item # CS38
$10.95
Item # CS36
Item # CS57
$22.50
Item # CS17
$8.50
Item # CS77
Side wheels made from a red urethane bonded to a metal core. Wheels come with bearings installed. 4 diameter, fit Clarke or Porter Cable 12, 504, and F89 drum sanders. (Back wheel is part #CS56)
$57.00
Item # CS01
$8.00
Item # CS127
Item # CS73
$3.50
Item # CS118
$12.96
Item # CS43
$35.05
Item # GAL134
Paper templates make it easier to cut the paper to fit your machine. Use the angle cut on the end of the template to get a perfect bend. These have a fixed length, so you may need to cut the paper a little longer or shorter to fit your machine. Fits Clarke 504 & Porter Cable F87.
Item # CS87
$55.38
Item # CS34
$63.58
Item # GAL115
$70.90
Item # CS02
$100.13
Item # CS95
Here are a few tips on using them.