Power Booster 220v 20amp Plug

Power booster to specifically run your 220v sander. This booster is designed for all 220v floor sanders. It will boost on average 24 volts above the line voltage. For one 220v sander hookup only. Digital Volt Meter Convenient Carry Handle 40 amp Circuit Breaker Electrical Capacity: 14.3 KVA rated at 62 amps Output:20 AMP standard 3 prong L6 connectors to sander (6214) Input: 20 AMP standard 3 prong L6 connectors from power source (6212) Output: (1) 230 volt 20 AMP twistlock Weight: 30 lbs...

$871.98

Item # A08

Power Booster 220v30amp Plug

Power booster to specifically run your 220v sander. This booster is designed for all 220v floor sanders. It will boost on average 10 percent above the line voltage. For one 220v sander hookup only. Digital Volt Meter Convenient Carry Handle Protective Rubber Feet 40amp Circuit Breaker Electrical Capacity: 14.3 KVA rated at 62 amps Output:30 AMP standard 3 prong L6 connectors to sander (6344) Input: 30 AMP standard 3 prong L6 connectors from power source (6342) Output: (1) 230 volt 30 AMP twistlock Weight: 25 lbs...

$879.42

Item # A09

Power Station +, Bona Booster

This power booster is rated at 30 amps 230 volts. It has a 30amp twist lock 230 volt outlet, as well as a 20amp 110 volt duplex receptacle. The Bona®Power Station Plus is the safe, inexpensive and convenient way to protect your valuable floor sanding equipment from high or low-voltage power situations. Use it as a power center to centrally connect your installation and floor sanding equipment. Use it to effectively run your floor sanding and vacuuming equipment, and adjust the power for your 230V units if your power supply drifts from the desired voltage range. Downtime is money out of your pocket. Your equipment is at tremendous risk for burnout during common job site situations such as when it is necessary to use extra long power cords; when the local utility gets hit with excessive demands for electricity; when you are forced to draw your power from a temporary power pole on a construction site; or when you assume a 230V source is delivering 230 volts. Play it safe and smart. Wit..

$1,157.84

Item # A06

Power Booster Clarke

For running 1 machine. This power booster has a 20amp 250 volt twist lock outlet. The Power Booster provides dedicated power outlets for any floor sanding jobsite and overcomes high and low voltage conditions with its boost and buck power selector switch. This tool is ideal for new construction projects where the power supply is limited and shared by various trades. Simply connect the power booster to the power source and control a personal isolated power source. The dedicated duplex circuit protected 120 V lines provide power for the operation of edgers, vacuums, compressors, saws and routers. The rugged digital LED readout voltmeter assures accurate output readings for peak performance of sanding machines and electrical operated tools. A simple 3-position operating switch provides quick selection of the mode needed: The boost position protects expensive electrical components from low voltage conditions and improves the machine performance. The buck position protec..

$1,104.00

Item # A03

Booster, Voltage 3 Ph Mack~

This 3 phase power booster is intended for use with rider systems. It has 3 outlets, so you can run 2 sanders and the rider each on its own cord...

$4,600.00

Item # A04

Splitter Box 25 Plast No 110

This box makes it easier to supply power to a sander and a dust collection system, or two sanders. The unit consists of a 25 foot 8 gage main cable, a 40 amp breaker in a water resistant box, and two 6 foot output leads with 30 amp plugs. Connect the 8 gage cable to a 60 amp breaker and run 2 machines off the outputs. The breaker is wired to trip both outputs in case of an overload. Note: This is not a power booster...

$414.04

Item # DSBOXSM