| Model |
Product Image |
Item Name |
Price |
| E13LE |
 |
NEW ECONOMY LED bulb will fit in existing light sockets for a much longer service life than standard bulbs. 5 watt LED with 37 watt output 400+ lumen... |
$10.99
Add:
|
| USE01 |
 |
This super pad is made from billet aluminum with an OEM style rubber face. We designed these pads because we were tired of hearing complaints about... |
$75.00
Add:
|
| E13 |
 |
Standard heavy duty bulb for 110v Clarke type edgers. 25 watt See our part number E13L for our replacement LED bulb that will not not burn out and is... |
$2.10
Add:
|
| EC25E |
 |
25 ft Economy Edger Cord Black with twist lock plug for edgers. Material is black STO 12/3 Twist lock plug is a 4731 (nema 5-15C) |
$45.30
Add:
|
| SN001 |
 |
This quick release bag clamp makes removing & reattaching dust bags easier on sanders. The clamp when fully expanded has a diameter of 4 inches.... |
$21.00
Add:
|
| CE67 |
 |
The caster pivot bearings on Super 7 edgers. These have a teflon seal to keep dust out. Also fits the edger wheel. |
$4.68
Add:
|
| CE09 |
 |
Replacement brushes for Super 7 edgers. Set of 4 brushes without wires (for brushes with wires, see part #CE57). We recommend replacing brushes when... |
$16.68
Add:
|
| CE57 |
 |
Replacement brushes for Super 7 edgers. Set of 4 brushes with wires (for brushes without wires, see part #CE09). We recommend replacing brushes when... |
$15.99
Add:
|
| CE04 |
 |
Set of 2 replacement brushes for Super 7 2-brush edgers. Note that most Super 7 edgers are 4-brush, make sure that you confirm which you need before... |
$13.32
Add:
|
| CE70 |
 |
Keep your edger in a case to prevent it getting damaged when transporting. Fits the Super 7 edger |
$92.91
Add:
|
| CE05T |
 |
Original factory design type wheel assembly with Teflon, Plastic wheel. Upgraded with a grade 5 stud and a lock nut to stop the assembly from... |
$29.00
Add:
|
| CE05U |
 |
Original factory wheel assembly with Urethane wheel from Clarke. Softer than steel to reduce wheel marks. Non-marking urethane material over steel... |
$52.12
Add:
|
| CE05 |
 |
Original factory design type wheel assembly with steel wheel. Upgraded with a grade 5 stud and a lock nut to stop the assembly from loosening up and... |
$25.00
Add:
|
| SW05 |
 |
Brush seater/commutator stone. To seat new brushes, run this stone over the surface of the commutator with the motor running. The abrasive from the... |
As low as $9.00
Add:
|
| CE72N |
 |
These swivel pipes are ideal for dust collection. They can be connected to a 1.5 hose, a 2 hose or a bag. Kit includes Dust pipe, Bag and rubber... |
$201.67
Add:
|
| CE75 |
 |
These skirts close up the gap between the edger and the floor, improving dust pickup. This is 3 short pieces, to go between the wheels. Fits Super 7... |
$10.00
Add:
|
| EDOLLY |
 |
The Edger Dolly is the backsaver for floor sanding professionals. The Edger Dolly is used to sit and lay on while edging floors. You can use the... |
$475.00
Add:
|
| KEL1 |
 |
This is our special grease mixture. The grease used by most manufacturers is too thick to flow into the gears. This mixture is thin enough to flow,... |
$9.50
Add:
|
| KEL1G |
|
This is our special grease mixture. The grease used by most manufacturers is too thick to flow into the gears. This mixture is thin enough to flow,... |
$134.38
Add:
|
| E20A |
 |
For removing and installing edger pads. This adjustable wrench can be adjusted to fit all edger pads. |
$32.69
Add:
|
| E05 |
 |
Replacement latch for Super 7 & B-2 edger cases. |
$13.82
Add:
|
| CE11 |
 |
Replacement paper retainer bolt for Super 7 Edger. Thin head, OEM size. This bolt does not have a hole for a cotter pin – if you need the hole, order... |
$1.86
Add:
|
| EC03 |
 |
16" Long pigtail with male twist lock plug. Fits Super 7, B-2 & Silverline edgers. May also fit some others. |
$19.90
Add:
|
| CE99 |
 |
The EZ Roll kit retrofits your edger with 1-5/8 diameter grey wheels. Not only do these roll better, they provide a little wider wheel base for... |
$102.74
Add:
|
| K600 |
 |
On-Off toggle switches for edgers. These are a 2-pole switch. This heavy-duty switch may be difficult to install due to its size. |
$100.00
Add:
|
| K508 |
 |
On-Off toggle switches for edgers. These are a 2-pole switch. Light duty. |
$9.95
Add:
|
| K508A |
 |
On-Off toggle switches for edgers. These are a 2-pole switch. Medium duty 20 amp @110v This is the edger switch we recommend for most Clarke Edgers... |
$11.00
Add:
|
| CE72 |
 |
Adapter kit for connecting your Super 7, Essex Silver Line SL7, or KT Blizzard edger to a 1.5 inch vacuum hose. Designed for the old style (fixed)... |
$19.00
Add:
|
| CE14 |
 |
For removing the paper bolt on Super 7 edgers. 9/16” hex, fits a 3/8 bolt head. |
$14.62
Add:
|
0 item(s) - $0.00
Machine Parts-> (67)
Used Equipment (3)
Machine Accessories
Featured Products ...
Bearing Size Chart
1. Switch, Med duty 20 Amp